硅酸盐学报

陶瓷复合装甲的孔加工及机理

作者：郑雷袁军堂李少华

单位：南京理工大学机械工程学院南京理工大学机械工程学院南京理工大学机械工程学院南京210094 南京210094 南京210094

分类号：TG506

出版年,卷(期):页码：2007,35(5):568-573

DOI：

摘要：

因组成材料的性能相差迥异,陶瓷复合装甲的加工十分困难。根据其组成材料的加工特性,研制了特定组分(结合剂体积分数为:48%Cu,30%Co,6%Ni,5%WC,5%Ti,4%Sn,2%Cr)的青铜基结合剂烧结金刚石套料钻进行孔加工,采用自来水冷却。通过单因素实验,研究了主轴转速以及轴向工作压力对加工效率的影响。按加工机理的不同,钻孔过程可分为3个阶段;研究了钻头的两种打滑现象并初步解释了成因。根据孔口的各种加工缺陷,提出了预压应力钻削法以改善孔口加工质量。结果表明,该加工技术具有实用价值。

Due to the great differences in the mechanical characteristics of the materials that compose ceramic composite armor,it is very difficult to machine.Considering the machining properties of these materials,special sintered diamond bits with a broze-based binder were developed.The composition(volume fraction)of the binder was 48% Cu,30% Co,6% Ni,5% WC,5% Ti,4% Sn and 2% Cr.Fresh water was used for coolant.Through single factor experiments,the effects of spindle speed and axial thrust on machining efficiency are presented.The drilling process is divided into three phases according to the diverse machining mechanisms.Then,the two kinds of skidding mechanisms of bits were researched.After analyzing the visual defects of the entry and exit of holes machined,drilling with com-pressive pre-stress to improve the cutting quality was investigated.The achievements resulting from this research are of practical value.

基金项目：

“十五”国防预研基金(404010502.1C)资助项目

作者简介：

参考文献：

[1]仲伟虹,张佐光,梁志勇.轻质陶瓷复合材料装甲抗弹机理的研究[J].兵器材料科学与工程,1998,21(3):19-22.ZHONG Weihong,ZHANG Zuoguang,LIANG Zhiyong.Ordnance Mater Sci Eng(in Chinese),1998,21(3):19-22. [2]徐燕申,田欣利,于爱兵,等.工程陶瓷材料加工技术的研究进展[J].中国机械工程,1996,7(6):59-63.XU Yanshen,TIAN Xinli,YU Aibing,et al.China Mech Eng(in Chi-nese),1996,7(6):59-63. [3]王瑞刚,潘伟,蒋蒙宁,等.可加工陶瓷及工程陶瓷加工技术现状及发展[J].硅酸盐通报,2001(3):27-35.WANG Ruigang,PAN Wei,JIANG Mengning,et al.Bull Chin Ceram Soc(in Chinese),2001(3):27-35. [4]黄春峰.工程陶瓷加工技术的发展与应用[J].工具技术,2000,34(12):3-6.HUANG Chunfeng.Tool Eng(in Chinese),2000,34(12):3-6. [5]HO C Y,LU J K.A closed form solution for laser drilling of silicon nitride and alumina ceramics[J].J Mater Process Technol,2003,140:260-263. [6]ZHANG Q H,ZHANG J H,JIA Z X,et al.Material-removal-rate analysis in the ultrasonic machining of engineering ceramics[J].J Ma-ter Process Technol,1999,88:180-184. [7]JIA Z X,ZHANG J H,AI X.Ultrasonic vibration pulse elec-tro-discharge machining of holes in engineering ceramics[J].J Mater Process Technol,1995,53:811-816. [8]袁军堂,马少杰,温玉林,等.高强有机纤维增强聚烯烃基复合材料加工技术[J].机械科学与技术,1999,18(2):283-285.YUAN Juntang,MA Shaojie,WEN Yulin,et al.Mech Sci Technol(in Chinese),1999,18(2):283-285. [9]胡宝刚,杨志翔,杨哲.复合材料后加工技术的研究现状及发展趋势[J].宇航材料工艺,2000(5):24-27.HU Baogang,YANG Zhixiang,YANG Zhe.Aerosp Mater Technol(in Chinese),2000(5):24-27. [10]BHATTACHARYYA D,HORRIGAN D P W.A study of hole drilling in Kevlar composites[J].Compos Sci Technol,1998,58:267-283. [11]赵祖虎.复合材料特种加工技术[J].宇航材料工艺,1998(4):32-34.ZHAO Zuhu.Aerosp Mater Technol(in Chinese),1998(4):32-34. [12]LAU W S,YUE T M,LEE T C,et al.Un-conventional machining of composite materials[J].J Mater Process Technol,1995,48:199-205. [13]HOCHENG H,HSU C C.Preliminary study of ultrasonic drilling of fiber reinforced plastics[J].J Mater Process Technol,1995,48:255-266. [14]宗文俊,李旦,王洪祥,等.金刚石刀具技术的发展状况[J].中国机械工程,2003,14(13):1165-1169.ZONG Wenjun,LI Dan,WANG Hongxiang,et al.China Mech Eng(in Chinese),2003,14(13):1165-1169. [15]亓曾笃.金刚石的耐热性[J].工业金刚石,2001(1):14-15.QI Zengdu.Ind Diamond(in Chinese),2001(1):14-15. [16]鲁凡.对孕镶金刚石钻头磨损规律的探讨[J].中南工业大学学报,1997,28(6):511-513.LU Fan.J Central South Univ Technol(in Chinese),1997,28(6):511-513. [17]刘银伟,靖向党.孕镶金刚石钻头工作层不均匀磨损原因的研究[J].探矿工程,2005,(4):56-58.LIU Yinwei,JING Xiangdang.Explor Eng(in Chinese),2005,(4):56-58. [18]王殿江.孕镶金刚石钻头钝化与锐化机制探讨[J].地质与勘探,1995,31(6):58-61.WANG Dianjiang.Geol Prospecting(in Chinese),1995,31(6):58-61.

服务与反馈：

【文章下载】【加入收藏】